Dry Ice Blasting Mold

Chemical-free mold removal for framing, attics, and crawl spaces

Dry Ice Blasting Mold in PALOS VERDES PENINSULA, California

Dry Ice Blasting Mold in PALOS VERDES PENINSULA, California is the fastest way to strip mold off structural lumber without soaking your home or leaving abrasive residue behind. We use dry ice mold removal PALOS VERDES PENINSULA crews on coastal homes from Lunada Bay to South Shores, where marine fog and winter rain keep wood framing damp for months. If you have spotted black mold behind drywall or smelled that musty odor in the attic, call (833) 929-5837 for a same-day look.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What Dry Ice Blasting Mold Includes

Every dry ice blasting mold job includes the full scope from inspection through clearance testing. Here is what you get, and what we quote separately if your property needs it.

01

Full Inspection and Testing

We walk the property with a thermal imaging camera and moisture meter, then check inside wall cavities with a boroscope camera. Air samples go to an accredited lab. You get the written scope and flat price within 24 hours of the inspection.

02

Containment and HEPA Filtration

We build plastic containment sheeting and ZIP wall barriers around the work zone, then run a negative air machine with HEPA filters. This keeps spores from drifting into the rest of your home during blasting. Setup takes about 90 minutes on a typical room.

03

Dry Ice Blasting of Affected Surfaces

A dry ice blasting machine fires rice-sized pellets at 300 to 500 mph to lift mold off framing, block, and metal. We work in 4-to-6 foot passes and check each section with a moisture meter. A typical attic takes 3 to 5 hours.

04

Antimicrobial and Encapsulant

After blasting, we apply an antimicrobial solution like Concrobium or Benefect to the bare wood. On exposed framing, we roll on an encapsulant coating such as Fiberlock ShockWave to seal the grain. This step takes 2 to 3 hours and cures overnight.

05

Post-Remediation Air Testing

We run a HEPA vacuum over the whole zone, then pull post-remediation air samples with a spore trap sampler. The lab compares spore counts to the outdoor baseline. You get the clearance report and a written 1-year workmanship warranty.

06

Photo Documentation for Insurance

We photograph every surface before and after, log moisture meter readings, and keep a written log of the work. That packet goes straight to your adjuster. Most carriers cover dry ice blasting remediation PALOS VERDES PENINSULA California when the mold traces to a covered water loss.

Service overview

What Dry Ice Blasting Mold in PALOS VERDES PENINSULA, California Does

Dry Ice Blasting Mold in PALOS VERDES PENINSULA, California is a media blasting method that fires soft dry ice pellets at 300 to 500 mph to lift mold, mildew, and surface contamination off wood, block, and metal. The pellets hit at roughly -109 degrees Fahrenheit, so the mold freezes and releases from the substrate instead of being scrubbed into it. There is no water, no sand, and no chemical residue to dry out. The pellets sublimate into carbon dioxide gas on contact, so the only cleanup is the mold you just removed.

Most of our calls come from homeowners who found mold after a slow plumbing leak, a failed roof flashing, or a foggy summer that kept a crawl space wet for weeks. We also handle dry ice mold removal PALOS VERDES PENINSULA jobs for property managers in Rolling Hills Estates and Miraleste who need a fast turnaround between tenants. If you have been searching for dry ice blasting mold near me in PALOS VERDES PENINSULA California, we can usually be on site the same day you call.

No Water, No Secondary DamageTraditional mold washing pushes water into framing, subfloor, and insulation, which feeds the next bloom. Dry ice leaves the wood dry enough to start antimicrobial treatment the same day. On a typical 400-square-foot attic, that saves 24 to 48 hours of drying time and prevents the secondary water damage that turns a $2,000 job into a $6,000 one.
Reaches Hidden FramingWe use a boroscope camera and thermal imaging camera to find mold behind drywall, under subfloor, and inside wall cavities before we start blasting. Dry ice reaches those surfaces without demolition in most cases. On a recent Palos Verdes Estates job, we cleaned 60 linear feet of wall framing through two small access cuts instead of removing 14 feet of drywall.
Safe for Wood and WiringDry ice is soft enough that it will not pit lumber, scar copper plumbing, or chew through electrical sheathing the way sandblasting or soda blasting can. We dial the pressure down for older 1920s and 1950s framing common in Malaga Cove and Valmonte. That means you keep original structural wood instead of replacing it.
Dry Ice Blasting Mold by Mold Remediation Service Palos Verdes Peninsula
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

Our Dry Ice Blasting Mold Process

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Inspection and Testing

We walk the property with a thermal imaging camera and moisture meter to map the moisture. A boroscope camera checks inside wall cavities and under subfloor. We pull air samples with a spore trap sampler and send them to a lab. You get the written scope and a flat price before we start, usually within 24 hours of the call.

Stage 1
02

Containment Setup

We build plastic containment sheeting and ZIP wall barriers around the work zone, then run a negative air machine with HEPA filters to keep spores from drifting into the rest of the house. A 10-by-12 foot room takes about 90 minutes to seal. Our crew wears disposable coveralls and respirator cartridges the whole time.

Stage 2
03

Dry Ice Blasting

A dry ice blasting machine fires rice-sized pellets at the mold. We work in 4-to-6 foot passes, checking each section with a moisture meter before moving on. A typical attic takes 3 to 5 hours. A crawl space under a 2,000-square-foot home runs 5 to 8 hours depending on how much framing is exposed.

Stage 3
04

Antimicrobial and Encapsulant

Once the surface is clean, we apply an antimicrobial solution like Concrobium or Benefect to the bare wood. On porous framing that will stay exposed, we roll on an encapsulant coating such as Fiberlock ShockWave to seal the grain. This step takes 2 to 3 hours and cures overnight.

Stage 4
05

Verification and Clearance

We run a HEPA vacuum over the whole zone, then pull post-remediation air samples. The lab compares spore counts to the outdoor baseline. If the numbers are clean, we hand you the clearance report and a written 1-year workmanship warranty. If they are not, we re-clean at no charge.

Stage 5

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Dry Ice Blasting Machine

Fires rice-sized dry ice pellets at 300 to 500 mph to lift mold off framing, block, and metal without water or abrasive media. This is the core tool for every dry ice blasting mold job.

02

Thermal Imaging Camera

Detects temperature differences that reveal hidden moisture behind drywall, under subfloor, and inside wall cavities. We use it during the inspection to map the moisture before we scope the job.

03

Boroscope Camera

Slides into wall cavities and under subfloor through small access holes. It lets us see mold growth without tearing out drywall. We photograph what we find and share the images with you.

04

Moisture Meter

Reads moisture content in wood and drywall. We check every section before and after blasting to confirm the surface is dry enough for antimicrobial treatment.

05

Negative Air Machine with HEPA Filters

Pulls air out of the containment zone and pushes it through HEPA filters. This keeps spores from drifting into the rest of the house during blasting. We run it for the entire job.

06

Spore Trap Sampler

Collects air samples before and after remediation. The lab compares indoor spore counts to outdoor baselines. This is how we verify the job is actually done.

07

Dri-Eaz and Phoenix Restoration Dehumidifiers

Pull residual moisture out of the air after blasting. We run them in crawl spaces and attics where ventilation is limited. A typical crawl space dries in 24 to 48 hours.

Use cases

When to Call for Dry Ice Blasting Mold

These examples show how the service framework adapts rather than forcing every call through one repair.

Dry Ice Blasting Mold
Attic Framing After a Roof LeakA Palos Verdes Estates homeowner found black mold on 40 linear feet of attic rafters after a roof leak went unnoticed for three weeks. Moisture meter readings were above 25 percent on the affected framing. The insulation below was damp and the attic smelled musty. → We contained the attic, blasted the rafters and sheathing with dry ice, and treated with antimicrobial solution. Moisture readings dropped below 12 percent within 24 hours. Post-remediation air testing came back clean, and the homeowner kept the original framing instead of replacing it.

Crawl Space Joists in Lunada Bay

A Lunada Bay home had mold covering 60 linear feet of floor joists and subfloor from years of ground moisture. The crawl space had no vapor barrier and the musty odor was spreading into the living room. The homeowner was worried the joists would need replacement. → We blasted the joists, subfloor, and block walls with dry ice, treated with antimicrobial solution, and installed a 6-mil vapor barrier. The musty odor cleared within a week. Two winters later, the framing is still clean and the homeowner checks it once a year.

Bathroom Wall Cavity in Miraleste

A Miraleste rental unit had mold behind the bathroom wall from a slow supply line leak. The tenant reported a musty smell and the property manager found discoloration on the baseboard. A boroscope camera confirmed mold on 12 linear feet of wall framing. → We cut two small access panels, contained the area, and blasted the framing with dry ice. The wall cavity was dry within 24 hours and we treated with antimicrobial solution. The clearance report came back clean in four days and the unit was re-listed the following week.

Problems we solve

Mold Problems We Solve on the Peninsula

Most mold calls on the Hill trace back to one of a few recurring problems. Here is what we see, what happens if you wait, and how we fix it.

ISSUE

Black mold behind drywall after a slow leak

We locate the leak with a thermal imaging camera, cut a small access panel, and blast the framing with dry ice. No water is added, so the wall cavity dries fast. We treat with antimicrobial, seal with encapsulant, and verify with air testing before closing up.

SYMPTOM

Attic mold on roof decking and rafters

We contain the attic, run a negative air machine, and blast the sheathing and rafters with dry ice. The wood stays dry, so we do not have to replace insulation. We finish with an antimicrobial treatment and a post-remediation air test.

SIGN

Crawl space mold from constant ground moisture

We blast the joists, subfloor, and block walls with dry ice, then treat with antimicrobial solution. We recommend a vapor barrier and a dehumidifier to keep the space dry. Most crawl spaces are clean in one day.

ALERT

HVAC mold spreading through the house

We inspect the air handler and ductwork with a boroscope camera, then blast the affected metal surfaces with dry ice. Ductwork gets HEPA vacuumed and treated with antimicrobial fog. We verify with air testing before you turn the system back on.

Pricing process

Dry Ice Blasting Mold Pricing

$2,200 - $9,000+ depending on scope

Phase 01

Square Footage Affected

The more surface area that needs blasting, the longer the job takes. A 400-square-foot attic runs 3 to 5 hours. A 1,200-square-foot crawl space can take two days. We measure during the inspection and quote by the square foot.

Phase 02

Access and Containment

Tight attics, low crawl spaces, and finished rooms with furniture all add setup time. Containment on a finished room takes about 90 minutes. A crawl space with a 24-inch access hatch takes longer to seal and ventilate.

Phase 03

Type of Surface

Bare framing blasts fast. Painted or sealed surfaces take longer because the mold bonds tighter. Block walls and concrete are slower than wood. We adjust the quote based on what we find during the inspection.

Questions before we arrive

Frequently Asked Questions About Dry Ice Blasting Mold

Dry Ice Blasting Mold
Call (833) 929-5837
How much does dry ice blasting mold cost in PALOS VERDES PENINSULA California?

Most residential jobs run $2,200 to $6,500 in 2026, depending on square footage and access. A single attic or crawl space averages $2,800 to $4,200. Whole-house remediation with multiple rooms can hit $9,000 or more. We give you a flat written price after the inspection, so you know the number before we start.

Is dry ice mold removal safe for wood in PALOS VERDES PENINSULA?

Yes. Dry ice is soft enough that it will not pit, gouge, or splinter structural lumber. We dial the pressure down for older framing common in Malaga Cove and Valmonte. The pellets freeze the mold and lift it off the surface without cutting into the wood grain. After blasting, the wood is dry and ready for antimicrobial treatment the same day.

How does dry ice blasting kill mold in PALOS VERDES PENINSULA California?

The pellets hit at -109 degrees Fahrenheit and 300 to 500 mph. That flash-freezes the mold and the kinetic energy lifts it off the substrate. The pellets sublimate into CO2 gas on contact, so nothing is left behind. We follow with an antimicrobial solution like Concrobium or Benefect to kill any remaining spores on the surface.

Does dry ice blasting require containment in PALOS VERDES PENINSULA California?

Yes, always. We build plastic containment sheeting and ZIP wall barriers around the work zone and run a negative air machine with HEPA filters. That keeps spores from drifting into the rest of your home during blasting. Containment setup adds about 90 minutes to the job but is required under California Department of Public Health guidelines.

Ready when you are

Get Dry Ice Blasting Mold in PALOS VERDES PENINSULA, California

Call (833) 929-5837 and we will schedule a same-day inspection for dry ice blasting mold in PALOS VERDES PENINSULA, California. You get a flat written price, a licensed and insured crew, and a clearance report when the job is done. We answer the phone 24/7.

Dry Ice Blasting Mold

Talk with the local team

Request Dry Ice Blasting Mold

Call us at (833) 929-5837 any time, day or night. We answer emergency calls 24/7 and schedule standard inspections same-day when you reach us before noon. Tell us what you are seeing or smelling and we will tell you what it likely takes to fix it.

2516 Vía Tejon, Palos Verdes Estates, CA 90274, USA, PALOS VERDES PENINSULA, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now